Skip to main content

Tezspire Dosage

Generic name: TEZEPELUMAB 210mg in 1.9mL
Dosage form: injection, solution
Drug class: Selective immunosuppressants

Medically reviewed by Drugs.com. Last updated on May 26, 2023.

Recommended Dosage

The recommended dosage of TEZSPIRE is 210 mg administered subcutaneously once every 4 weeks.

Missed Dose Information

If a dose is missed, administer the dose as soon as possible. Thereafter, the patient can continue (resume) dosing on the usual day of administration. If the next dose is already due, then administer as planned.

Preparation and Administration Instructions

TEZSPIRE vial and pre‑filled syringe are intended for administration by a healthcare provider.

TEZSPIRE pre-filled pen can be administered by patients/caregivers or healthcare providers. Patients/caregivers may administer TEZSPIRE pre-filled pen after proper training in subcutaneous injection technique and after the healthcare provider determines it is appropriate.

Each vial, pre-filled syringe and pre‑filled pen contain a single dose of TEZSPIRE.

Prior to administration, remove TEZSPIRE from the refrigerator and allow it to reach room temperature. This generally takes 60 minutes. Do not expose to heat and do not shake. Do not use if the security seal on the carton has been broken. Do not put back in the refrigerator once TEZSPIRE has reached room temperature.
Visually inspect TEZSPIRE for particulate matter and discoloration prior to administration. TEZSPIRE is a clear to opalescent, colorless to light yellow solution. Do not use TEZSPIRE if liquid is cloudy, discolored, or if it contains large particles or foreign particulate matter. Do not use if the vial, pre-filled syringe or pre‑filled pen has been dropped or damaged or if the expiration date has passed.
Inject TEZSPIRE 210 mg (contents of one vial, one pre-filled syringe or one pre-filled pen as described below) subcutaneously into the thigh or abdomen, except for the 2 inches (5 cm) around the navel. If a healthcare provider or caregiver administers the injection, the upper arm can also be used. A patient should not self-inject in the upper arm. TEZSPIRE should not be injected into areas where the skin is tender, bruised, erythematous, or hardened. It is recommended to rotate the injection site with each injection.

Administration Instructions for Single-Dose Pre-filled Syringe

Refer to Figure 1 to identify the pre-filled syringe components for use in the administration steps.

Do not remove the needle cover until Step 2 of these instructions when you are ready to inject TEZSPIRE. Do not touch the needle guard activation clips to prevent premature activation of the needle safety guard.

Figure 1 TEZSPIRE Pre-filled Syringe Components

Figure_1
1.

Grasp the syringe body to remove the pre-filled syringe from its tray. Do not grab the pre-filled syringe by the plunger.

The pre-filled syringe may contain small air bubbles; this is normal. Do not expel the air bubbles prior to administration.

2.
Number_3_picture

Do not remove the needle cover until ready to inject. Hold the syringe body and remove the needle cover by pulling straight off. Do not hold the plunger or plunger head while removing the needle cover. You may see a drop of liquid at the end of the needle. This is normal.

3.
number4picture

Gently pinch the skin and administer subcutaneously at approximately 45° angle into the recommended injection site (i.e., upper arm, thigh, or abdomen).

4.
number5picture

Inject all of the medication by pushing in the plunger all the way until the plunger head is completely between the needle guard activation clips. This is necessary to activate the needle guard.

5.
number6picture

After injection, maintain pressure on the plunger head and remove the needle from the skin. Release pressure on the plunger head to allow the needle guard to cover the needle. Do not re-cap the pre-filled syringe.

6.

Discard the used syringe into a sharps container.

Administration Instructions for Single-Dose Pre-filled Pen

These administration instructions are intended for healthcare providers use only. Patients and caregivers should refer to the TEZSPIRE pre-filled pen ‘Instructions for Use’ for more detailed instructions on the preparation and administration of TEZSPIRE pre-filled pen [See Instructions for Use].

Patients/caregivers may inject after proper training in subcutaneous injection technique according to the ‘Instructions for Use’, and after the healthcare provider determines it is appropriate.

Refer to Figure 2 to identify the pre-filled pen components for use in the administration steps.

Do not remove the cap until you are ready to inject TEZSPIRE.

Figure 2 TEZSPIRE Pre-filled Pen Components

figure_2_pre-filled_pen_components
1.

Grab the middle of the pre-filled pen body to remove the pre-filled pen from its tray.

The pre-filled pen may contain small air bubbles; this is normal. Do not expel the air bubbles prior to administration.

2.
figure_2-image-2

Do not remove the cap until ready to inject. Hold the pre-filled pen body with 1 hand and carefully pull the cap straight off with your other hand. Do not touch the needle or push the orange needle guard with your finger. Do not put the cap back on the pre-filled pen. You could cause the injection to happen too soon or damage the needle.

3.

Gently pinch the skin at the injection site or give the injection without pinching the skin.

Inject TEZSPIRE by following the steps into the recommended injection site (i.e., upper arm, thigh, or abdomen).

When injecting, you will hear the first click that tells you the injection has started. Press and hold the pre-filled pen for 15 seconds until you hear the second click. Do not change the position of the pre-filled pen after the injection has started.

4.
figure2_image-4

Position the pre-filled pen. Place the orange needle guard flat against the skin (90‑degree angle). Make sure you can see the viewing window.

5.
figure_2_image_5

Press down firmly until you cannot see the orange needle guard. You will hear the first ‘click’, this tells you the injection has started. The orange plunger will move down in the viewing window during the injection.

6.
figure_2_image_6

Hold down firmly for about 15 seconds. You will hear a second ‘click’, this tells you the injection has finished. The orange plunger will fill the viewing window.

7.
figure_2_image_7

After you have completed the injection, lift the pre-filled pen straight up. The orange needle guard will slide down and lock into place over the needle.

8.

Discard the used pre-filled pen into a sharps container.

Frequently asked questions

Further information

Always consult your healthcare provider to ensure the information displayed on this page applies to your personal circumstances.