Liquid-90

Contains: water, 7732-18-5; sodium hydroxide, 1310-73-2; sodium hypochlorite, 7681-52-9; sodium polyacrylate, 9003-04-7.

Directions For Use

USE DILUTIONS - CLEANING PIPELINE MILKERS

0-12 grains hardness: 1 oz per 2.6 mL/L (3 gallons) hot water (71°C/160°F)

12-18 grains hardness: 1 oz per 3.9 mL/L (2 gallons) hot water (71°C/160°F)

More than 18 grains hardness: 1 1/2 oz per 5.9 mL/L (2 gallons) hot water (71°C/160°F)

USE DILUTIONS - SPRAY OR MECHANICAL WASHINGS OF BULK TANKS

0-18 grains hardness: 3/4 oz per 5.9 mL/L (1 gallon) hot water (71°C/160°F)

More than 18 grains hardness: 1 1/2 oz per 11.7 mL/L (1 gallon) hot water (71°C/160°F)

For Agriculture Use

Cleaning Pipelines and Milking Units

1. Pre-flush pipelines and milking units with large volume of potable water.

2. Prepare wash solution using 1 ounce of Liquid-90 to each 3 gallons of hot water. Temperature must not go below 100°F/38°C during the wash cycle.

3. Circulate wash solution through system for 6-8 minutes. Brush-wash all parts not coming in contact with the wash solution. Wear impervious gloves when brush-washing equipment.

4. Rinse with large volume of potable water to remove all wash solution. Allow to drain.

5. Add proper use dilution of an EPA registered acid sanitizer to acid rinse and sanitize in one easy step, or use the proper dilution of a pipeline acid cleaner to acid rinse the system. Allow to drain.

6. Just before milking (no sooner than 30 minutes), sanitize by circulating proper ppm solution of a recommended sanitizer. Drain completely.

Cleaning Bulk Tanks

1. Pre-flush bulk tank with large volume of potable water.

2. Prepare wash solution in volume necessary to properly operate the spray device, using 1 ounce of Liquid-90 per each 2 gallons of hot water. Temperature must not go below 100°F/38°C during the wash cycle.

3. Spray-wash for 8-10 minutes. Disconnect return line and drain. Inspect all milk zone surfaces for cleanliness. Prepare wash solution using 4 ounces of a chlorinated manual cleaner and not more than 1 gallon of hot water. Brush-wash valve, outside of tank and any part of tank not cleaned by spraying system. Wear impervious gloves when brush-washing equipment.

4. Rinse inside and outside of bulk tank with potable water to remove all wash solution. Allow to drain.

5. See steps 5 and 6 above.

*Where local or state regulations are in effect, consult authorities for additional information.

Remove or protect food products and packaging materials prior to using this product.

Avoid food contamination during application and storage.

Rinse surfaces thoroughly with potable water after use.

This product is not for use as a sanitizer or disinfectant.

Consult your Ecolab representative for specific use instructions and recommended dispensing equipment.

Danger

Causes severe skin burns and eye damage.

Wash skin thoroughly after handling. Wear protective gloves/ protective clothing/eye protection/face protection. Mixing this product with acid or ammonia releases chlorine gas.

IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. IF ON SKIN (or hair): Remove/ Take off immediately all contaminated clothing. Rinse skin with water/ shower. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER/doctor. Wash contaminated clothing before reuse.

READ SAFETY DATA SHEET (SDS) BEFORE USING THIS PRODUCT

EMERGENCY HEALTH INFORMATION: 1 800 328 0026. If located outside the United States and Canada, call collect 1 651 222 5352 (number is in the US).

This product may be patented: www.ecolab.com/patents

Ecolab, 1 Ecolab Place, St. Paul MN 55102 USA

tel. 1 800 392 3392

© 2018 Ecolab USA Inc.

All rights reserved

Made in United States

www.ecolab.com

CPN: 1449048.0