BioSentry 904 Disinfectant (Canada)
This treatment applies to the following species:- Beef Cattle
- Cats
- Chickens
- Dairy Cattle
- Dogs
- Ducks
- Geese
- Horses
- Laboratory animals
- Ostrich
- Quail
- Sheep
- Swine
- Turkeys
Poultry Hatchery, Farm Premises and Animal Care Disinfectant
AGRICULTURAL
FOR USE IN FOOD PROCESSING PLANTS/CAUSES SEVERE SKIN BURNS AND EYE DAMAGE
CONTENTS MAY BE HARMFUL
READ THE LABEL BEFORE USING
KEEP OUT OF REACH OF CHILDREN
DANGER • CAUTION
CORROSIVE
POISON
Active Ingredients |
|
Didecyl dimethyl ammonium chloride |
9.2% w/w |
Alkyl (C12-67%, C14-25%, C16-7%, C18-1%) dimethyl benzyl ammonium chloride |
7.6% w/w |
Alkyl (C12-40%, C14-50%, C16-10%) dimethyl benzyl ammonium chloride |
6.2% w/w |
DIN 02319756
BioSentry 904 Disinfectant is effective in 400 ppm hard water (as CaCO3). Disinfects in 5% organic soil load. Recommended for chicken, turkey, duck, quail, goose, ostrich and other avian hatcheries. Effective in poultry, swine and livestock (including equine) premises. Useful in laboratory animal and animal breeder facilities.
BioSentry 904 Disinfectant contains sequestering agents, to prevent the precipitation of minerals and metals from hard water.
● deodorizes by killing most microorganisms that cause offensive odours.
● contains no perfume to mask or hide any odours that might exist.
BROAD SPECTRUM GERMICIDAL ACTION IN HARD WATER AND UNDER SOIL LOAD CONDITIONS: At four (4) mL per liter (1:250) in official A.O.A.C. Use-Dilution and Fungicidal Tests, BioSentry 904 Disinfectant is effective in water up to 400 ppm hardness (as CaCO3) and an organic soil load of 5% serum, against the following organisms:
BACTERIA
Alcaligenes faecalis |
ATCC 8748 |
Bordetella avium |
ATCC 35086 |
Enterobacter aerogenes |
ATCC 63809 |
Enterococcus faecium (Streptococcus faecalis) |
ATCC 6569 |
Escherichia coli |
ATCC 11229 |
Klebsiella pneumoniae |
ATCC 4352 |
Pasteurella multocida |
ATCC 7707 |
Proteus mirabilis |
ATCC 25933 |
Proteus morganii |
ATCC 25830 |
Pseudomonas aeruginosa |
ATCC 15442 |
Salmonella enterica |
ATCC 10708 |
Salmonella enteriditis |
ATCC 4931 |
Salmonella gallinarum |
ATCC 9184 |
Salmonella pullorum |
ATCC 9120 |
Salmonella typhosa |
ATCC 6539 |
Serratia marcescens |
ATCC 264 |
Shigella dysenteriae |
ATCC 13313 |
Shigella sonnei |
ATCC 29930 |
Staphylococcus aureus |
ATCC 6538 |
Streptococcus agalactiae |
ATCC 27916 |
Streptococcus pyogenes |
ATCC 9547 |
FUNGI
Aspergillus fumigatus |
ATCC 10894 |
Candida albicans |
ATCC 18804 |
Trichophyton mentagrophytes var. interdigitale |
ATCC 9533 |
VIRUSES/MYCOPLASMA: Using accepted virus propagation and hard surface test methods, BioSentry 904 Disinfectant is effective at 1:250 in 400 ppm hard water and 5% serum against the following viruses and mycoplasma:
Avian Flu (H5H1) Birnavirus |
ATCC VR-478 |
Canine parvovirus canin |
ATCC VR-953 |
Coronavirus |
ATCC VR-22 |
Coronavirus |
ATCC VR-763 |
Herpesvirus |
ATCC VR-135 |
Herpesvirus |
ATCC VR-783 |
Mycoplasma gallisepticum |
ATCC 15302 |
Mycoplasma iners |
ATCC 19705 |
Parainfluenza |
ATCC VR-281 |
Paramyxovirus |
ATCC VR-109 |
Porcine Epidemic Diarrhea |
ATCC VR-109 |
Precautions
KEEP OUT OF REACH OF CHILDREN.
DANGER Do not get in eyes, on skin or on clothing. Do not swallow. Do not breathe fume/gas/mist/vapors/spray. Do not mix with other cleaning or disinfecting compounds. Handle with care. Wash thoroughly after handling. Wear chemical-resistant gloves made of any waterproof material, suitable protective clothing and eye/face protection. Ensure adequate ventilation of the working area. In case of insufficient ventilation, wear suitable respiratory equipment. Do not use on feeders or waterers and do not allow contact with food, feed or drinking water.
FIRST AID TREATMENT: Contains: Didecyl dimethyl ammonium chloride, 9.2% w/w; Alkyl dimethyl benzyl ammonium chloride (C12 -67%, C14 -25%, C16 -7%, C18 -1%), 7.6% w/w; Alkyl dimethyl benzyl ammonium chloride (C12 -40%, C14 -50%, C16 -10%), 6.2% w/w. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting, unless advised to do so by a doctor. If inhaled, remove to fresh air and keep at rest in a position comfortable for breathing. If in eyes, rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If on skin, rinse well with water. If on clothes, remove clothes. Rinse mouth thoroughly. Never give anything by mouth to an unconscious person.
Storage
1. Store at room temperature 20C.
2. Store in original container in areas inaccessible to children.
3. Do not store on side.
4. Avoid creasing or impacting of side walls.
5. Do not use or store near heat or open flame.
Disposal
1. Rinse the emptied container thoroughly and add the rinsings to the treatment site.
2. Follow provincial instructions for any required additional cleaning of the container prior to its disposal or reconditioning.
3. Make the empty container unsuitable for further use.
4. Dispose of the container in accordance with provincial requirements.
5. For information on the disposal of unused, unwanted product and the clean up of spills, contact the Provincial Regulatory Agency.
Directions For Use
BioSentry 904 Disinfectant is a complete, chemically balanced disinfectant that provides clear use solutions even in cold water. Kills a broad range of gram-negative and gram-positive bacteria, fungi and viruses associated with the avian hatching industry, poultry, swine and livestock (including equine) premises, laboratory animal facilities and kennels. (See antimicrobial efficacy chart on the container label.)
DIRECTIONS FOR USE IN FOOD PROCESSING PLANTS: Remove all debris and other deposits from hard, non-porous surfaces to be cleaned or disinfected. Prepare a solution of 4 mL BioSentry 904 Disinfectant per litre of water. Apply liquid with a mop, sponge or cloth, or by spraying, to thoroughly wet surfaces. A minimum contact time of 10 minutes is required for disinfection. For food contact surfaces, scrub and rinse well with potable water before they are reused.
DIRECTIONS FOR USE IN AVIAN HATCHERIES: For disinfecting precleaned surfaces: Use BioSentry 904 Disinfectant to disinfect precleaned non-porous surfaces including hatchers, setters, trays, racks, egg flats, walls, floors, ceilings and other surfaces in the hatchery environment. It is also excellent for chick boxes, egg cases, vans and trash containers.
Preclean the surface to be disinfected with a BioSentry hatchery cleaner. Rinse and if possible let surfaces dry. Then, apply BioSentry 904 Disinfectant at four (4) mL per litre of water (0.40%) by immersion, by flowing solution over treated surfaces, by use of a soft coarse spray, with a clean mop or cloth, or through a foaming apparatus. Thoroughly wet surfaces. Surfaces should remain moist for 10 minutes for complete disinfection.
NOTE: Do not spray BioSentry 904 Disinfectant solutions unless workers are protected from breathing the spray mist.
SANITIZING HATCHERY ROOMS BY FOG APPLICATION: Close room off so fog is confined to the room to be treated. Mix one (1) part BioSentry 904 Disinfectant to five (5) parts water. Insert the nozzle of the fogger through a suitable opening into the room. With the setting on maximum output, fog for one (1) to three (3) minutes for each 113 cubic meters of space in the room (4000 ft3). Duration of fogging time is dependent on type of fogging equipment used. Refer to fogger instructions. Under no circumstances should a room or building be entered by anyone within 4 hours or until fog has completely settled.
NOTE: The fog generated is very irritating to the eyes, skin and mucous membranes. Under no circumstances should a room or building be entered by anyone until the fog has completely settled, normally 1 - 4 hours after the actual fogging. If feeders and waterers were not removed from the premises during treatment, or were not adequately covered to prevent contact with treatment, they should be washed with detergent and water before use for poultry or livestock. If the building or room must be entered before the fog completely settles, then individuals entering the building or room must wear a self-contained respirator approved be NIOSH/MSHA, goggles, long shirt sleeves and pants.
SANITIZING INCUBATORS AND HATCHERS BY FOGGING: Prepare a stock solution of 45 mL BioSentry 904 Disinfectant to 1 litre of water. Fog 90 - 240 mL of this into setters and hatchers immediately after transfer. Repeat daily in setters and every 12 hours in hatchers. Discontinue hatcher treatments approximately 24 hours prior to pulling the hatch. Do not allow people to contact or breathe this fog and do not enter machines until the fog has settled (30 - 60 minutes after fogging is completed). To do this, install permanent fogging nozzles in setters and hatchers and use an air compressor to disperse the sanitizing solution as a fog. Contact your BioSentry Technical Representative if you need assistance.
It is also satisfactory to fog setters and hatchers with 4 mL of BioSentry 904 Disinfectant per litre of water. If this is done, fog for 30 - 90 seconds once per hour or once every two hours. Contact your BioSentry Technical Representative for assistance.
NOTE: If the building or room must be entered before the fog completely settles, then individuals entering the building or room must wear a self-contained respirator approved be NIOSH/MSHA, goggles, long shirt sleeves and pants.
DISINFECTING CHICK VANS, EGG TRUCKS, HATCHERY AND FARM VEHICLES: Clean and rinse vehicles and disinfect with 4 mL BioSentry 904 Disinfectant per litre of water. Rinse after 10 minutes contact. BioSentry 904 Disinfectant should not be mixed with other cleaning or disinfecting compounds or products.
DIRECTIONS FOR USE ON POULTRY, SWINE AND LIVESTOCK (INCLUDING EQUINE) FARMS
GENERAL FARM DISINFECTANT USES: (4 mL per litre, 1:250)
a. Remove all livestock and feeds from premises, trucks, coops or crates to be treated.
b. Remove all litter, bedding and manure from floors, walls and surfaces of facilities traversed or occupied by animals.
c. Empty all feeding devices and watering appliances.
d. Clean all surfaces with water or water and a compatible detergent.
e. Saturate all surfaces with BioSentry 904 Disinfectant diluted at 4 mL per litre of water using a brush, cloth, mop or mechanical spraying device. Small items (forks, shovels, scrapers) may be immersed. Treated surfaces must remain moist for at least 10 minutes for proper germicidal action.
f. Ventilate buildings, trucks, coops and other closed spaces. Do not house livestock or use equipment until treatment has thoroughly dried.
g. Thoroughly scrub all feeding and watering equipment with detergent and rinse with potable water before reuse.
VEAL, CALVING, HOG, CATTLE AND HORSE OPERATIONS: Between depopulations of facilities, cleaning and disinfection of pens, hutches, aisles, ventilation equipment, utensils and other environmental surfaces may be required. Flush soils from these areas and clean and disinfect with 4 mL of BioSentry 904 Disinfectant per litre of water. Take care to avoid disinfectant use solution contact with animals, feed, feed equipment, water or watering devices as indicated above. If spray contacts feeders or waterers, scrub them and rinse well with potable water before they are reused.
BOOT BATH: Use 8 mL of BioSentry 904 Disinfectant per litre of water (1:125) in boot baths. Change solution daily and anytime it becomes visibly soiled. Use a nylon bristled brush to clean soils from boots.
SANITIZING POULTRY HOUSES AND LIVESTOCK BUILDINGS USING BIOSENTRY 904 DISINFECTANT VIA THERMAL FOGGING: After the building has been depopulated and cleaned as in (a) (b) (c) and (d) under «General Farm Disinfectant Uses», double check to be sure all people, poultry, livestock and pets have vacated the building. Close all windows, doors, louvers, curtains, etc., making the building as closed and tight as possible. Mix one (1) part BioSentry 904 Disinfectant with two (2) parts water in the reservoir of the fogger. With the setting on maximum output, fog the treatment into the room or building to be sanitized. Use a total of one litre of BioSentry 904 Disinfectant for each 186 square meters of floor space. If the area is more than 8 meters high, use two (2) litres per 186 square meters of floor space. In multi-story buildings, the application must be repeated for each floor that is to be sanitized. The fogger itself may be placed just inside the door of the building to be treated, or the nozzle of the fogger may be inserted through a suitable opening in the door or building. The opening should be just large enough to accommodate the nozzle. After fogging, the building should be kept closed for twenty-four hours. After twenty-four hours the fog should have settled and the building can then be opened and aired. The building should be opened for a minimum of twenty-four hours before it is repopulated with poultry or livestock.
NOTE: The fog generated is very irritating to the eyes, skin and mucous membranes. Under no circumstances should a room or building be entered by anyone within 4 hours or until the fog has completely settled. If the building or room must be entered before the fog completely settles, then individuals entering the building or room must wear a self-contained respirator approved be NIOSH/MSHA, goggles, long shirt sleeves and pants. If feeders and waterers were not removed from the premises during treatment, or were not adequately covered to prevent contact with treatment, they should be washed with detergent and water before use for poultry and livestock.
DIRECTIONS FOR USE IN ANIMAL CARE FACILITIES, ANIMAL RESEARCH CENTERS, ANIMAL BREEDING FACILITIES, KENNELS AND ANIMAL QUARANTINE AREAS: BioSentry 904 Disinfectant is a one-step germicide, fungicide, soapless cleaner and deodorant effective in the presence of organic soil (5% serum). It is non-selective and, when used as directed, will not harm tile, terrazzo, resilient flooring, concrete, painted surfaces, varnished wood, glass or metals.
● To clean and disinfect hard surfaces, use 4 mL of BioSentry 904 Disinfectant per litre of water (1:250). Apply by immersion, flushing solution over treated surfaces or with a mop, sponge, cloth or bowl mop to thoroughly wet surfaces. Prepare fresh solutions daily or when solution becomes visible dirty.
● To clean badly soiled areas, use up to 12 mL per litre of water (1:83).
● To disinfect, allow treated surfaces to stand for at least 10 minutes before wiping or rinsing.
● To control mold and mildew growth on previously cleaned, hard non-porous surfaces, use 4 mL of BioSentry 904 Disinfectant per litre of water. Allow to dry without wiping. Reapply as a new growth appears.
NOTICE TO USER: This product is to be used only in accordance with the directions on the primary container labelling.
Medical 1-800-498-5743
? 1-800-621-8829
Manufactured By:
HACCO, Inc., 110 Hopkins Dr., Randolph, WI 53956 U.S.A.
Distributed By:
Neogen Canada, Inc. 7323 Roper Rd NW Edmonton, AB T6E 0W4
Questions? Comments? 1-800-621-8829
BioSentry® a Registered Trademark of BioSentry, Inc.; Used Under Exclusive License to Neogen® Corporation.
Net Contents: |
Item # |
|
3.8 Litres/1 Gallon |
D12709557-CAN |
BK970170-1022 |
5 Gallons/18.93 Litres |
D12709737-CAN |
LA220390-1-1022 ENG |
55 Gallons/208 Litres |
D12695581-CAN |
LA220312-1-1022 ENG |
CPN: 1636001.2
A Neogen Company
110 HOPKINS DRIVE, RANDOLPH, WI, 53956
Telephone: | 1-800-621-8829 |
THIS SERVICE AND DATA ARE PROVIDED "AS IS". Animalytix assumes no liability, and each user assumes full risk, responsibility, and liability, related to its use of the Animalytix service and data. See the Terms of Use for further details. |
Copyright © 2024 Animalytix LLC. Updated: 2024-08-26